← All projects
ArduinoBluetoothUSBAndroid

Arduino Multimeter

Build a multimeter on an Arduino Nano and read it on your phone. The app also turns your phone into an oscilloscope, a sound generator and a serial monitor.

Difficulty: easyMain parts: Arduino Nano, HC-05Phone: Android 6.0 or newer

Multimeter app measuring 12 V DC with a live graph
What it does

One small board, many instruments

You don't have to build everything. Each part of the circuit is independent: build only the instruments you need. The only part you always need is the Arduino with the Bluetooth module.

  • DC voltage
  • DC current
  • Resistance, 3 ranges
  • Continuity with beep
  • Capacitance
  • Inductance
  • Temperature
  • Oscilloscope
  • Sound generator
  • Resistor colour code
  • Serial monitor
  • Flashlight

Needs the Arduino boardWorks with the phone alone

The app

Everything on one screen

Big readings, a live graph you can zoom, HOLD, and notes to save a value with a name. Save a graph to a file and open it again later in GRAPHS.

Oscilloscope showing a 500 Hz sine wave
No board needed

Oscilloscope

Shows the signal from the headphone input with peak-to-peak, frequency, period and RMS. Calibrate it once with a known signal.

Sound generator set to a 440 Hz sine
No board needed

Sound generator

Sine, square, triangle and saw from 20 Hz to 20 kHz, with amplitude and duty cycle.

Resistor colour code calculator
No board needed

Resistor colour code

Tap the colours of a 4, 5 or 6 band resistor to read its value and tolerance.

Serial monitor receiving readings from the board
Any device

Serial monitor

Talk to any Arduino or module over Bluetooth or a USB-serial adapter: send commands, see text or HEX, set the baud rate.

Settings with the Bluetooth connection

Easy connection

Search, pair and connect to the HC-05 right in the app, or switch to USB.

Main screen with readings and the live graph

Live graph

Every reading goes on the graph. Pause to scroll back, zoom in, or save it with a name.

Shopping list

What you need

Multimeter board

  • Arduino Nano or Uno1
  • Bluetooth module HC-05 or HC-061
  • Temperature sensor TMP361
  • Resistor 10 kΩ3
  • Resistor 100 kΩ3
  • Resistor 220 Ω1
  • Resistor 1.8 kΩ1
  • Resistor 3.1 kΩ1
  • Resistor 13 kΩ1
  • Shunt 0.015 Ω1
  • Capacitor 0.1 mF1

Inductance meter (optional)

  • Comparator LM3391
  • Resistor 150 Ω1
  • Resistor 330 Ω1
  • Capacitor 1 µF, non-polarized1
  • Diode 1N41481

Also useful

A single-sided copper board to make the PCB, or a breadboard to test first. Test leads and a 3.5 mm jack cable for the oscilloscope.

Step by step

Build and connect

  1. 1

    Build the circuit

    Use a breadboard to try it out, or make the printed circuit board for a tidy, reliable result. There are two schematics: the multimeter itself, and the inductance meter, which connects to the same Arduino. Tap a schematic to open it full size.

    On the top side of the board, jumper marks show which points to join: ip_1 connects to the other ip_1, and so on. There are five jumpers, ip_1 to ip_5. The videos show how to make the board with the iron method and solder everything.

  2. 2

    Upload the Arduino sketch

    Download the ZIP and open multimetro_digital_premium_v1.1.0.ino in the Arduino IDE. Choose your board (Arduino Nano or Uno) and the port, then press Upload.

    The HC-05 connects to pins D11 (to the module's RXD) and D12 (to its TXD) at 9600 baud, the module's default speed, so you can leave it connected while uploading.

    New in sketch v1.1.0: steadier voltage, resistance and inductance readings, and the app can tell when nothing is connected to the input. Older sketches still work with the new app.
  3. 3

    Connect the app

    Power the board. In the app open SETTINGS, choose Bluetooth and press SEARCH. Tap PAIR next to HC-05 (if it asks for a PIN, try 1234 or 0000). When it moves to Paired devices, tap it and the app connects right away. Next time, press SYNC on the main screen to reconnect.

    Settings screen with the HC-05 connected
    1Pair and connect
    Main screen showing Connected
    2Readings arrive
    On Android 11 and older, turn on Location to search for new devices. Already paired devices work without it.
  4. 4

    Connect the test leads

    Every measurement uses the common GND pin plus one positive pin:

    • VoltageGND + MV(+)
    • Resistance and continuityGND + MO(+)
    • CurrentGND + AMP
    • CapacitanceGND + CAP(+)
    • InductanceGND + inductance
    For resistance, connect the SW pin to one of the range pins with a switch: 0–220, 220–10k or 10k–300k. In RES and CONT the app shows BOARD SWITCH: tap the matching position, 220 Ω, 10 kΩ or 100 kΩ. Without SW connected, resistance and continuity don't work.
  5. 5

    Calibrate for better accuracy

    All the calibration values are together at the top of the sketch. With everything connected, measure with another multimeter and enter your real values:

    • 5V pin voltageSUPPLY_VOLTS
    • 3.3V pin voltageAREF_VOLTS
    • Resistance referencesR_REF_220 R_REF_10K R_REF_100K
    • Voltage dividerDIVIDER_TOP DIVIDER_BOTTOM
    • Ammeter shuntSHUNT_OHMS

    Upload the sketch again after changing them. Solder all the parts: loose breadboard contacts add resistance and make readings less accurate.

Oscilloscope

Using the oscilloscope

The oscilloscope doesn't need the Arduino. The signal goes through a small protection circuit into the phone's headphone (microphone) input, so your phone needs a 3.5 mm jack or an adapter. To calibrate, feed a signal of known size, tap UNCAL and enter its peak-to-peak voltage.

Protect your phone. With the divider from the schematic, the input can take at most 30 V, and the voltage reaching the phone must never be higher than 3.7 V.
Downloads

Get everything

Multimeter Free

All features, with ads. A one-time purchase in the app removes them.

Google Play

Multimeter Pro

The same app, paid once, never any ads.

Google Play

Schematic, PCB and sketch

Arduino sketch v1.1.0, schematics and PCB files v1.0.4 in one ZIP (14 MB).

Download ZIP
Stuck? Write to me at necodesarrollo@gmail.com or on Telegram @neco_desarrollo. Almost every problem can be fixed. If the project helped you, you can support it with a donation.